CaseIH IRONBuilder Product Selection

Your Summary

LB 3 SERIES LARGE SQUARE BALERS

STATUS: NOT COMPLETE

CONFIGURED PRICE:	$ NA USD
ACCESSORIES:	$ NA USD

TOTAL:

$ NA USD

† Taxes, freight, setup and delivery not included.

Standard Features Print Summary Save Configuration

Clear Options | Go To Accessories

1. Select a product

2. Select a model

3. Options

4. Accessories

5. Summary

6. Request a quote

2. Select a model

LB333 Packer Cutter Square Baler [ Standard Features ]

BALE SIZE:
35.4 in. (H) x 31.5 in. (W) (90 cm x 80 cm) 98 in. (2.5 m) maximum bale length "Silage Ready" baler

PTO TRACTOR HOOK-UP:
1-3/8 21-Spline 1000 PTO Heavy-duty slip clutch with over running clutch Swivel ball hitch (requires tractor clevis hitch)

PICK-UP:
77 in./2.0m pick-up width at deflectors 70 in./1.8m pick-up width at outside tines 56 Double tines on 4 tine bars Large 15 x 6.00-6, 4 PR pick-up tires (2)

PACKER CUTTER:
Packer: 3 forks, 6 double tines (6) Maximum number of knives (spring protected) Cutting length with (6) knives - 4.5 in. average

PRE-COMPRESSION CHAMBER:
Charge chamber with crop sensor plates Anti-friction floor Gearbox driven stuffer assembly Stuffer fork-type with 6 tines

TRANSPORT:
Highway transport chain Parking jack Road lights Work lights Conveniently located toolbox

PURCHASED PROTECTION:
The Case IH Protection Plan (CPP) is available for this model. BALE CHAMBER: Plunger speed - 42 strokes per minute Plunger stroke - 28 in. (710mm) Plunger drive - direct from gearbox Bale ejector (standard and partial bale) with rear controls standard on all balers Roller chute standard on all balers

KNOTTERS:
350 lb. MINIMUM REQUIREMENT knot strength twine (4) Heavy-duty double-tie knotters Knotter drive - gearbox and shaft Twine capacity - 30 balls (2) Knotter fans

BALER CONTROL / MONITORING:
Bale density system - adjustable, automatic In-cab baler control system - black & white display ISOBUS 11783 standard compatible Bale drop indicator (roller chute only) Automatic centralized greasing system with quick fill adaptor Automatic chain lubrication system

Requirements for Operation:
Tractor Requirements: 1000 rpm PTO, 1-3/8 in. 21 Spline 110 PTO horsepower MINIMUM, 130 PTO horsepower recommended Hammerstrap clevis hitch (3) tractor remotes - Raise/lower pickup - Bale ejector and roller chute raise/lower - Packer cutter knives raise/lower Implement brakes required on all equipment towed at 50 Kph (31mph) or higher
LB333 Rotor Cutter Square Baler [ Standard Features ]

BALE SIZE:
35.4 in. (H) x 31.5 in. (W) (90 x 80 cm) 2.5 m 98 in. maximum bale length "Silage Ready" baler

PTO TRACTOR HOOK-UP:
1-3/8 21-Spline 1000 PTO Heavy-duty slip clutch with over running clutch Swivel ball hitch (requires tractor clevis hitch)

PICK-UP:
77 in./2.0m pick-up width at deflectors 70 in./1.8m pick-up width at outside tines 56 Double tines on 4 tine bars (rubber mounted) Large 15 x 6.00-6, 4 PR pick-up tires (2)

ROTOR CUTTER:
Rotor cutter width: 38 in./97 cm Rotor cutter diameter: 26 in./65 cm Spiral style rotor with offset length lobes Rotor speed: 86 rpm Cut-out clutch with automatic re-engaging Direct transfer of crop to pre-compression chamber (23) Knives with minimum spacing of 1.5 in./39mm Hydraulic engagement of knives from tractor Knife drawer slides to left side of baler for full service access Blanking plates replace knives when not in use Automatic re-engaging springs protect knives

PRE-COMPRESSION CHAMBER:
Charge chamber with crop sensor plates Anti-friction floor Gearbox driven stuffer assembly Stuffer fork-type with 6 tines

BALE CHAMBER:
Plunger speed - 42 strokes per minute Plunger stroke - 28 in. (710mm) Plunger drive - direct from gearbox Bale ejector (partial and standard bale) with rear controls standard on all balers Roller chute standard on all balers

KNOTTERS:
350 lb. MINIMUM REQUIREMENT knot strength twine (4) Heavy-duty double-tie knotters Knotter drive - gearbox and shaft Twine capacity - 30 balls (2) Knotter fans

BALER CONTROL / MONITORING:
Bale density system - adjustable, automatic In-cab baler control system - black & white display ISOBUS 11783 standard compatible Bale drop indicator (roller chute only) Automatic centralized greasing system with quick fill adaptor Automatic chain lubrication system

TRANSPORT:
Highway transport chain Parking jack Road lights Work lights Conveniently located toolbox

PURCHASED PROTECTION:
The Case IH Protection Plan (CPP) is available for this model. Requirements for Operation: 1000 rpm PTO, 1-3/8 in. 21 Spline 130 PTO horsepower MINIMUM, 145 PTO horsepower recommended Hammerstrap clevis (3) Tractor remotes - Raise/lower pickup - Bale ejector and roller chute raise/lower - Raise/lower cutter knives and knife drawer Implement brakes required on all equipment towed at 50 Kph (31mph) or higher
LB333 Standard (No Cutter) Square Baler [ Standard Features ]

BALE SIZE:
35.4 in. (H) x 31.5 in. (W) (90 x 80 cm) 98 in. (2.5 m) maximum bale length "Silage Ready" baler

PTO TRACTOR HOOK-UP:
1-3/8 21-Spline 1000 PTO Heavy-duty slip clutch with over running clutch Swivel ball hitch (requires tractor clevis hitch)

PICK-UP:
77 in./2.0m pick-up width at deflectors 70 in./1.8m pick-up width at outside tines 56 Double tines on 4 tine bars Large 15 x 6.00-6, 4 PR pick-up tires (2)

PRE-COMPRESSION CHAMBER:
Packer: 2 forks, 4 double tines Pre-Compression chamber with crop sensor plates Gearbox driven stuffer assembly Stuffer fork-type with 4 tines

BALE CHAMBER:
Plunger speed - 42 strokes per minute Plunger stroke - 28 in. (71cm) Plunger drive - direct from gearbox Bale ejector (standard and partial bale) with rear controls standard on all balers Roller chute standard on all balers

KNOTTERS:
350 lb. MINIMUM REQUIREMENT knot strength twine (4) Heavy-duty double-tie knotters Knotter drive - gearbox and shaft Twine capacity - 30 balls (2) Knotter fans

BALER CONTROL / MONITORING:
Bale density system - adjustable, automatic In-cab baler control system - black & white display ISOBUS 11783 standard compatible Bale drop indicator (roller chute only) Automatic centralized greasing system with quick fill adaptor Automatic chain lubrication system Quick release chamber pressure

TRANSPORT:
Highway transport chain Parking jack Road lights Work lights Conveniently located toolbox

PURCHASED PROTECTION:
The Case IH Protection Plan (CPP) is available for this model.

Requirements for Operation:
Tractor Requirements: 1000 rpm PTO, 1-3/8 in. 21 spline 102 PTO horsepower MINIMUM, 120 PTO horsepower recommended Hammerstrap clevis hitch (2) tractor remotes - Raise/lower pickup - Bale ejector and roller chute raise/lower Implement brakes required on all equipment towed at 50 Kph (31mph)
LB433 Rotor Cutter Square Baler [ Standard Features ]

BALE SIZE:
35.4 in. (H) x 47.2 in. (W) (90 cm x 120 cm) 98 in. (2.5 m) maximum bale length "Silage Ready" baler

PTO TRACTOR HOOK-UP:
1-3/4 20-Spline 1000 PTO Heavy-duty slip clutch with over running clutch ASAE Cat III drawbar (requires tractor clevis hitch)

PICK-UP:
88 in./2.2m pick-up width at deflectors 81 in./2.1m pick-up width at outside tines 68 Rubber mounted tines on 4 tine bars Large 15 x 6.00-6, 4 PR pick-up tires (2)

ROTOR CUTTER:
Rotor cutter width: 54 in./135 cm Rotor cutter diameter: 26 in./65 cm Spiral style rotor with offset length lobes Rotor speed: 86 rpm Cut-out clutch with automatic re-engaging Direct transfer of crop to pre-compression chamber (17) Knives with minimum spacing of 3.1 in./80mm Hydraulic engagement of knives from tractor Knife drawer slides to left side of baler for full service access Blanking plates replace knives when not in use Automatic re-engaging springs protect knives

PRE-COMPRESSION CHAMBER:
Charge chamber with crop sensor plates Anti-friction floor Gearbox driven stuffer assembly Stuffer fork-type with 6 tines

BALE CHAMBER:
Plunger speed - 42 strokes per minute Plunger stroke - 28 in. (710mm) Plunger drive - direct from gearbox Bale ejector (standard and partial bale) with rear controls standard on all balers Roller chute standard on all balers

KNOTTERS:
350 lb. MINIMUM REQUIREMENT knot strength twine (6) Heavy-duty double-tie knotters Knotter drive - gearbox and shaft Twine capacity - 30 balls (3) Knotter fans

BALER CONTROL / MONITORING:
Bale density system - adjustable, automatic In-cab baler control system - black & white display ISOBUS 11783 standard compatible Bale drop indicator (roller chute only) Automatic centralized greasing system with quick fill adaptor Automatic chain lubrication system Quick release chamber pressure

TRANSPORT:
Highway transport chain Parking jack Road lights Work lights Conveniently located toolbox

PURCHASED PROTECTION:
The Case IH Protection Plan (CPP) is available for this model.

Requirements for Operation:
Tractor requirements: 1000 rpm PTO, 1-3/4 in 20 spline 150 PTO horsepower MINIMUM, 175 PTO horsepower recommended Hammerstrap clevis hitch (3) Tractor remotes - Raise/lower pick-up - Bale ejector and roller chute raise/lower - Raise/lower cutter knives and knife drawer Implement brakes required on all equipment towed at 50 Kph (31mph) or higher
LB433 Standard (No Cutter) Square Baler [ Standard Features ]

BALE SIZE:
35.4 in. (H) x 47.2 in. (W) (90 cm x 120 cm) 98 in. (2.5 m) maximum bale length "Silage Ready" baler

PTO TRACTOR HOOK-UP:
1-3/4 20-Spline 1000 PTO Heavy-duty slip clutch with over running clutch ASAE Cat III drawbar (requires tractor clevis hitch)

PICK-UP:
88 in./2.2m pick-up width at deflectors 81 in./2.1m pick-up width at outside tines 64 Double tines on 4 tine bars Large 15 x 6.00-6, 4 PR pick-up tires (2)

PRE-COMPRESSION CHAMBER:
Packer: 3 forks, 6 single tines Charge chamber with crop sensor plates Gearbox driven stuffer assembly Stuffer fork-type with 6 tines

BALE CHAMBER:
Plunger speed - 42 strokes per minute Plunger stroke - 28 in. (710mm) Plunger drive - direct from gearbox Bale ejector (standard and partial bale) with rear controls standard on all balers Roller chute standard on all balers

KNOTTERS:
350 lb. MINIMUM REQUIREMENT knot strength twine (6) Heavy-duty double-tie knotters Knotter drive - gearbox and shaft Twine capacity - 30 balls (3) Knotter fans

BALER CONTROL / MONITORING:
Bale density system - adjustable, automatic In-cab baler control system - black & white display ISOBUS 11783 standard compatible Bale drop indicator (roller chute only) Automatic centralized greasing system with quick fill adaptor Automatic chain lubrication system Quick release chamber pressure

TRANSPORT:
Highway transport chain Parking jack Road lights Work lights Conveniently located toolbox

PURCHASED PROTECTION:
The Case IH Protection Plan (CPP) is available for this model.

Requirements for Operation:
Standard: 1000 rpm PTO, 1-3/4 in. 20 Spline 125 PTO horsepower MINIMUM, 145 PTO horsepower recommended Hammerstrap clevis hitch (2) tractor remotes - Raise/lower pickup - Bale ejector and roller chute raise/lower Implement brakes required on all equipment towed at 50 Kph (31mph)

** Prices quoted are Manufacturer Suggested Retail Prices and are not valid outside of the United States of America. Please see your local dealer for a competitive quote in your local currency. Configurations and pricing must be reviewed by a Case IH dealer for accuracy, and to account for any applicable finance programs, discounts, trade-in values or desired supplemental service and/or support offerings. PDI, freight, other charges, equipment setup not included. CNH America LLC reserves the right to revise the Manufacturer Suggested Retail Prices.