2. Select a model

• Axial-Flow 5088 Combine

  STANDARD FEATURES
  ENGINE:
  

  Diesel, 6 cylinder, Cummins 8.3L, 265 SAE hp Electronically controlled fuel injection Power rise - 25 hp Includes wastegate turbo-charger and air-to-air intercooler Engine inlet air grid heater Complies with EPA Emission Requirements (Tier III) 250 gallon fuel tank Water trap fuel filter Key switch fuel/engine shut off Air filter - dual stage, dry type w/aspirated pre-cleaner and in-cab service indicator 200 AMP alternator Two 12 volt batteries - 950 CCA each Side mounted engine air screen with Power Clean evacuation system. Radiator, in-line core with deaeration reservoir Engine coolant filter and conditioner Muffler

  CHASSIS:
  

  Composite, hinged trim panels with transport locking pins Tool box Tie down shipping points Chassis rear tow points Back up safety alarm Service platforms Right front service ladder (2) 10 lb. dry chemical (ABC) fire extinguishers

  ADVANCED FARMING SYSTEMS:
  

  Pre-wired for AFS yield and moisture sensors, AFS Accuguide and GPS antenna

  HYDRAULICS:
  

  Closed center system: header lift, reel lift, unloader swing and steering Open center system: reel drive, unloader engage, feeder and separator engage and power brakes Electro-hydraulic control system for separator, feeder, unloader swing, unloader engage, reel raise/lower, reel fore/aft and header lift Single point/single lever header multi-coupler

  FEEDER:
  

  Single lever header quick attach Undershot-slatted with friction drive slip clutch Feeder reverser, electrically controlled, hydraulic Three strand roller chain with bolted slats Feeder silencer ready (2) 2.95 inch (75 mm) diameter lift cylinders

  CLEANING:
  

  Auger bed with 5 extended wear augers and single point cleanout control Cross Flow™ cleaning fan - includes low air flow adjustment for grass seeds, variable speed with cab controls, 450/1250 RPM Left side fan air inlet shield/screen Residue discharge dual speed External sieve adjustment

  OPERATOR'S CAB:
  

  GENERAL Tinted glass with front sun visor Right side full view service door Tilt open rear window Two dome lights and right console light Cab exit delay lighting

  GENERAL Tilting steering column, floor and upper pivot Deluxe windshield wiper w/two blades Adjustable right console, floats with seat Air suspension seat w/seat belt, lumbar adjustment, fore/aft isolator, operator's presence switch and adjustable LH arm rest Padded instructor seat w/storage compartment and seat belt Beverage holders Automatic temperature control heater/defroster and air conditioner Radio-ready - includes wiring, antenna and two speakers Mounting and power supply for electronic equipment and accessories. Alert horn Pressurizer fan Pivot forward ladder w/flexible lower step

  INSTRUMENTATION AND CONTROLS
  

  Variable recirculation fan Multifunctional propulsion control lever: feeder raise/lower, reel raise/lower and fore/aft, header height resume, unloader swing, unloader engagement, feeder / header emergency stop, shift function. Instrumentation package (back lighted): ground speed, engine speed, fan speed, rotor speed, shaft speed monitor (8 function), engine low RPM warning, hydraulic reservoir oil level, hydraulic oil temperature warning, unloader on/out indicators, engine and separator hour meter, auto feeder cutoff, diagnostic and troublshooting functions, area counter, low fuel warning, grain scan monitor, header cutting height indicator Engine power indicator

  OPERATORS CAB: (continued)
  

  INSTRUMENTATION AND CONTROLS Roading hydraulic safety lockout Unloader engage Unloader swing Separator engage Feeder/header engage Auto header height control with fine adjust and 2 height settings plus headland setting. Electronically controlled header raise/lower rates Automatic reel speed control Electric park brake control Electric concave clearance adjustment w/position display Electronic tailings volume monitor Electronic header recognition Service interval reminders Separator trip hour meter Adjustable alarm volume

  TRANSMISSION, BRAKES AND FINAL DRIVES:
  

  3 speed hydrostatic drive Hydraulic power disc brakes Electrically controlled, mechanically applied park brake Heavy-duty final drives with 12/73 gears

  THRESHING AND SEPARATING ROTOR:
  

  30 in. diameter AFX rotor 3 speed ranges with variable speed electric control in each range, 250-1125 RPM, enhanced rotor drive components Adjustable transport vanes

  CONCAVES:
  

  3 section bar and wire Electronic in-cab position control

  GRATES:
  

  3 Section

  GRAIN HANDLING:
  

  Grain tank capacity: 250 bushels Unloading rate: 2.5 bushels/second Quick raise and lower grain tank extensions Foldable bubble up auger Adjustable grain tank level sensor Unloading auger spill saver Operator deck grain tank sample access Grain tank front window No tools required grain tank cross auger cover adjustment Unloader clutch hydraulically controlled Spring loaded 2 speed chain drive for clean grain elevator Clean Outs: Clean grain and tailings auger drop-out troughs Clean grain elevator boot Front and rear grain tank cross auger trough access covers (right hand side) Vertical unload auger door

  GAUGES:
  

  Fuel level, coolant temperature, engine oil pressure

  TELLITES AND AUDIBLE ALARM:
  

  Engine oil pressure, charging system warning indicator Parking brake engage/low pressure Coolant temperature Grain tank full Engine intake manifold air temperature Engine air filter Tranmission shift

  LIGHTING:
  

  ASAE standard road lighting 6 halogen headlights (4 flood, 2 distance hi/low) Work lights (1 grain tank, 1 unloader) 2 tail, 4 combination amber flashing and turn signals 2 under cab after cut lights 2 rear work lights 2 mirror mounted side finder lights Portable service light, magnetic base with (4) combine connection points

  MAXIMUM HEADERS:
  

  Grain Head - 30 ft. (9.1 m) Grain Head Flex - 30 ft. (9.1 m) Draper Head - Rigid - 30 ft. (9.1 m) Draper Head - Flex - 30 ft. (9.1 m) Corn Head (30 in.), 8-row Chopping Corn Head (30 in.), 6-row Factory authorized chopping head (30in.), 6-row
• Axial-Flow 6088 Combine

  STANDARD FEATURES
  ENGINE:
  

  Diesel, 6 cylinder, Cummins 8.3L, 305 SAE hp Electronically controlled fuel injection Power rise - 25 hp Engine inlet air grid heater Includes wastegate turbo-charger and air-to-air intercooler Complies with EPA Emission Requirements (Tier III) Key switch fuel / engine shut-off 250 gallon fuel tank Water trap fuel filter Air filter - dual stage, dry type w/aspirated pre-cleaner and in-cab service indicator 200 AMP alternator Two 12 volt batteries - 950 CCA each Side mounted engine air screen with Power Clean evacuation system. Radiator, in-line core with deaeration reservoir Engine coolant filter and conditioner Muffler

  CHASSIS:
  

  Composite, hinged trim panels with transport locking pins Tool box Tie down shipping points Chassis rear tow points (2) 10 lb. dry chemical (ABC) fire extinguishers Back up safety alarm Service platforms Right front service ladder

  ADVANCED FARMING SYSTEMS:
  

  Pre-wired for AFS yield and moisture sensors, AFS Accuguide and GPS antenna

  HYDRAULICS:
  

  Closed center system: header lift, reel lift, unloader swing and steering Open center system: reel drive, unloader engage, feeder and separator engage and power brakes Electro-hydraulic control system for separator, feeder, unloader swing, unloader engage, reel raise/lower, reel fore/aft and header lift Single point/single lever header multi-coupler

  FEEDER:
  

  Single lever header quick attach Undershot-slatted with friction drive slip clutch Feeder reverser, electrically controlled, hydraulic Three strand roller chain with bolted slats Feeder silencer ready (2) 2.95 inch (75 mm) diameter lift cylinders

  CLEANING:
  

  Auger bed with 5 extended wear augers and single point cleanout control Cross Flow™ cleaning fan - includes low air flow adjustment for grass seeds, variable speed with cab controls, 450/1250 RPM Left side fan air inlet shield/screen Fan air inlet bottom shield/screen Residue discharge dual speed External sieve adjustment (chaffer center section and shoe)

  OPERATOR'S CAB:
  

  GENERAL Tinted glass with front sun visor Right side full view service door Tilt open rear window Two dome lights and right console light Cab exit delay lighting GENERAL Tilting steering column, floor and upper pivot Deluxe windshield wiper w/two blades Adjustable right console, floats with seat Air suspension seat w/seat belt, lumbar adjustment, fore/aft isolator, operator's presence switch and adjustable LH arm rest Padded instructor seat w/storage compartment and seat belt Beverage holders Automatic temperature control with heater/defroster and air conditioner Radio-ready - includes wiring, antenna and two speakers Mounting and power supply for electronic equipment and accessories. Alert horn Pressurizer fan Pivot forward ladder w/flexible lower step

  INSTRUMENTATION AND CONTROLS
  

  Variable recirculation fan Multifunctional propulsion control lever: feeder raise/lower, reel raise/lower and fore/aft, header height resume, unloader swing, unloader engagement, feeder / header emergency stop, shift function. Instrumentation package (back lighted): ground speed, engine speed, fan speed, rotor speed, shaft speed monitor (8 function), engine low RPM warning, hydraulic reservoir oil level, hydraulic oil temperature warning, unloader on/out indicators, engine and separator hour meter, auto feeder cutoff, diagnostic and troublshooting functions, area counter, low fuel warning, grain scan monitor, header cutting height indicator

  OPERATOR'S CAB: (continued)
  

  INSTRUMENTATION AND CONTROLS Roading hydraulic safety lockout Unloader engage Unloader swing Separator engage Feeder/header engage Auto header height control with fine adjust and 2 height settings plus headland setting. Electronically controlled header raise/lower rates Automatic reel speed control Electric park brake control Electric concave clearance adjustment w/position display Electronic tailings volume monitor Electronic header recognition Engine power indicator Service interval reminders Separator trip hour meter Adjustable alarm volume

  TRANSMISSION, BRAKES AND FINAL DRIVES:
  

  3 speed hydrostatic drive Hydraulic power disc brakes Electrically controlled, mechanically applied park brake Heavy-duty final drives with 12/73 gears

  THRESHING AND SEPARATING ROTOR:
  

  30 in. diameter AFX rotor 3 speed ranges with variable speed electric control in each range, 250-1125 RPM, enhanced rotor drive components Adjustable transport vanes

  CONCAVES:
  

  3 section bar and wire Electronic in-cab position control

  GRATES:
  

  3 Section

  GRAIN HANDLING:
  

  Grain tank capacity: 300 bushels Unloading rate: 3.0 bushels/second Quick raise and lower grain tank extensions Foldable bubble up auger Adjustable grain tank level sensor Unloading auger spill saver Operator deck grain tank sample access Grain tank front window No tools required grain tank cross auger cover adjustment Unloader clutch hydraulically controlled Spring loaded 2 speed chain drive for clean grain elevator Clean Outs: Clean grain and tailings auger drop-out troughs Clean grain elevator boot Front and rear grain tank cross auger trough access covers (right hand side) Vertical unload auger door

  GAUGES:
  

  Fuel level, coolant temperature, engine oil pressure

  TELLITES AND AUDIBLE ALARM:
  

  Engine oil pressure, charging system warning indicator Parking brake engage/low pressure Coolant level Grain tank full Engine intake manifold air temperature Engine air filter

  LIGHTING:
  

  ASAE standard road lighting 6 halogen headlights (4 flood, 2 distance hi/low) Work lights (1 grain tank, 1 unloader) 2 tail, 4 combination amber flashing and turn signals 2 under cab after cut lights 2 mirror mounted side finder lights 2 rear work lights Portable service light, magnetic base, with (4) combine connection points.

  MAXIMUM HEADERS:
  

  Grain Head - 30 ft. (9.1 m) Grain Head Flex - 35 ft. (10.7 m) Draper Head - Rigid - 40 ft. (12.2 m) Draper Head - Flex - 35 ft. (10.7 m) Corn Head (30 in.), 12-row Chopping Corn Head (30 in.), 8-row Folding Chopping Corn Head (30 in.), 8-row
• Axial-Flow 7088 Combine

  STANDARD FEATURES
  ENGINE:
  

  Diesel, 6 cylinder, Cummins 9.0L, 325 SAE hp Electronically controlled fuel injection Power rise - 25 hp Power boost - 25 hp (while unloading) Engine inlet air grid heater Includes wastegate turbo-charger and air-to-air intercooler Complies with EPA Emission Requirements (Tier III) Key switch fuel / engine shut-off 250 gallon fuel tank Water trap fuel filter Air filter - dual stage, dry type w/aspirated pre-cleaner and in-cab service indicator 200 AMP alternator Two 12 volt batteries - 950 CCA each Side mounted engine air screen with Power Clean evacuation system. Radiator, in-line core with deaeration reservoir Engine coolant filter and conditioner Muffler

  CHASSIS:
  

  Composite, hinged trim panels with transport locking pins Tool box Tie down shipping points Chassis rear tow points (2) 10 lb. dry chemical (ABC) fire extinguishers Back up safety alarm Service platforms Right front service ladder

  ADVANCED FARMING SYSTEMS:
  

  Pre-wired for AFS yield and moisture sensors, AFS Accuguide and GPS antenna

  HYDRAULICS:
  

  Closed center system: header lift, reel lift, unloader swing and steering Open center system: reel drive, unloader engage, feeder and separator engage and power brakes Electro-hydraulic control system for separator, feeder, unloader swing, unloader engage, reel raise/lower, reel fore/aft and header lift Single point/single lever header multi-coupler

  FEEDER:
  

  Single lever header quick attach Undershot-slatted with friction drive slip clutch Feeder reverser, electrically controlled, hydraulic Three strand roller chain with bolted slats Feeder silencer ready (2) 2.95 inch (75 mm) diameter lift cylinders

  CLEANING:
  

  Auger bed with 5 extended wear augers and single point cleanout control Cross Flow™ cleaning fan - includes low air flow adjustment for grass seeds, variable speed with cab controls, 450/1250 RPM Left side fan air inlet shield/screen Fan air inlet bottom shield/screen Residue discharge dual speed External sieve adjustment (chaffer center section and shoe)

  OPERATOR'S CAB:
  

  GENERAL Tinted glass with front sun visor Right side full view service door Tilt open rear window Two dome lights and right console light Cab exit delay lighting GENERAL Tilting steering column, floor and upper pivot Deluxe windshield wiper w/two blades Adjustable right console, floats with seat Air suspension seat w/seat belt, lumbar adjustment, fore/aft isolator, operator's presence switch and adjustable LH arm rest Padded instructor seat w/storage compartment and seat belt Beverage holders Automatic temperature control with heater/defroster and air conditioner Radio-ready - includes wiring, antenna and two speakers Mounting and power supply for electronic equipment and accessories. Alert horn Pressurizer fan Pivot forward ladder w/flexible lower step

  INSTRUMENTATION AND CONTROLS
  

  Variable recirculation fan Multifunctional propulsion control lever: feeder raise/lower, reel raise/lower and fore/aft, header height resume, unloader swing, unloader engagement, feeder / header emergency stop, shift function. Instrumentation package (back lighted): ground speed, engine speed, fan speed, rotor speed, shaft speed monitor (8 function), engine low RPM warning, hydraulic reservoir oil level, hydraulic oil temperature warning, unloader on/out indicators, engine and separator hour meter, auto feeder cutoff, diagnostic and troublshooting functions, area counter, low fuel warning, grain scan monitor, header cutting height indicator

  OPERATOR'S CAB: (continued)
  

  INSTRUMENTATION AND CONTROLS Roading hydraulic safety lockout Unloader engage Unloader swing Separator engage Feeder/header engage Auto header height control with fine adjust and 2 height settings plus headland setting. Electronically controlled header raise/lower rates Automatic reel speed control Electric park brake control Electric concave clearance adjustment w/position display Electronic tailings volume monitor Electronic header recognition Engine power indicator Service interval reminders Separator trip hour meter Adjustable alarm volume

  TRANSMISSION, BRAKES AND FINAL DRIVES:
  

  3 speed hydrostatic drive Hydraulic power disc brakes Electrically controlled, mechanically applied park brake Heavy-duty final drives with 12/73 gears

  THRESHING AND SEPARATING ROTOR:
  

  30 in. diameter AFX rotor 3 speed ranges with variable speed electric control in each range, 250-1125 RPM, enhanced rotor drive components Adjustable transport vanes

  CONCAVES:
  

  3 section bar and wire Electronic in-cab position control

  GRATES:
  

  3 Section

  GRAIN HANDLING:
  

  Grain tank capacity: 300 bushels Unloading rate: 3.0 bushels/second Quick raise and lower grain tank extensions Foldable bubble up auger Adjustable grain tank level sensor Unloading auger spill saver Operator deck grain tank sample access Grain tank front window No tools required grain tank cross auger cover adjustment Unloader clutch hydraulically controlled Spring loaded 2 speed chain drive for clean grain elevator Clean Outs: Clean grain and tailings auger drop-out troughs Clean grain elevator boot Front and rear grain tank cross auger trough access covers (right hand side) Vertical unload auger door

  GAUGES:
  

  Fuel level, coolant temperature, engine oil pressure

  TELLITES AND AUDIBLE ALARM:
  

  Engine oil pressure, charging system warning indicator Parking brake engage/low pressure Coolant level Grain tank full Engine intake manifold air temperature Engine air filter

  LIGHTING:
  

  ASAE standard road lighting 6 halogen headlights (4 flood, 2 distance hi/low) Work lights (1 grain tank, 1 unloader) 2 tail, 4 combination amber flashing and turn signals 2 under cab after cut lights 2 mirror mounted side finder lights 2 rear work lights Portable service light, magnetic base, with (4) combine connection points.

  MAXIMUM HEADERS:
  

  Grain Head - 30 ft. (9.1 m) Grain Head Flex - 35 ft. (10.7 m) Draper Head - Rigid - 40 ft. (12.2 m) Draper Head - Flex - 40 ft. (12.2 m) Corn Head (30 in.), 12-row Chopping Corn Head (30 in.), 8-row Folding Chopping Corn Head (30 in.), 8-row
• Axial-Flow 7120 Combine

  STANDARD FEATURES
  ENGINE:
  

  Diesel, 6 cylinder, Case IH 9L, 360 SAE hp Electronically controlled fuel injection Complies with EPA Emissions Requirements (Tier 3) Operator selectable power modes: Power boost mode: Power rise - 30 hp Unloading power boost - 25 hp Power rise mode: Power rise - 55 hp Air to air intercooler 277 gallon (1050 liter) fuel tank Key switch fuel/engine shut-off Water separator fuel filter and fuel cooler Water- in fuel sensor Air filter - dual stage dry type w/aspirated pre-cleaner In-cab service indicator 12 volt 185 amp alternator Two 12 volt batteries - 950 CCA each 24 volt starting system Engine grid heater Iso-mounted radiator, in-line core w/pressurized de-aerating tank Hinged, swing out oil cooler and AC cooler Metal rotary air screen

  GROUND DRIVE:
  

  11/111 Bull gear final drive 117 cc pump and 107 cc motor Electric shift 4 speed w/ hydrostatic drive Heavy-duty propulsion system 20 mph (32 kph) max road speed

  BRAKES:
  

  Manual dual caliper disc Electro-hydraulically released, spring applied park brake

  CHASSIS:
  

  Composite, hinged trim panels with transport locking pins Chassis jacking points Tie down shipping points Chassis tow points Tool box Service tool connection Combine reverse safety alarm Service platforms on both sides of chassis Fan bottom shield Two 10 lb. dry chemical fire extinguishers

  ADVANCED FARMING SYSTEMS:
  

  Yield and moisture sensors. AFS decals and badges.

  HYDRAULICS:
  

  Closed center load sensing system Single point/single lever header multi-coupler Electro-hydraulic control: Feeder raise/lower with variable rate control Reel fore & aft, raise/lower Unloader swing, Unloader drive clutch Separator Drive (Includes rotor drive, cleaning sieves, elevator drive and straw chopper drive) Feeder drive clutch Hydraulic Drives: Reel speed control Cross Flow Plus™ cleaning fan with speed control Dual straw spreader drive with adj. speed control Ride control feeder lift circuit accumulator

  FEEDER:
  

  Single lever header quick attach 54 in. (1,366 mm) wide Wear resistant floor and chain supports Undershot-serrated slat conveyor Four strand, 3 section conveyor with bolt on slats Mechanical shaft drive w/ modulated clutch engagement Independent hydraulic feeder / header reverser Feeder face adjustable fore & aft pitch Spring loaded front feeder drum Two 3 in. (75 mm) dia lift cylinders Friction type safety clutch for rock trap beater and independent radial pin safety clutch for conveyor chain Feeder safety stand

  CLEANING:
  

  Self leveling cleaning system Full width 15 in diameter Cross Flow Plus™ fan clean out door Adjustable pre-cleaner sieve Active grain pan system Electronic in cab sieve adjust with opening indicator Full cleaning system width sieve grain loss sensor Tri-SweepTailings Processor System with cleanout door Tailings volume sensor

  ELECTRICAL:
  

  Data Bus serial communications system Exterior lighting (6) stadium roof lights (2) under cab after cut lights Left and right side lights (1) grain tank, (1) unloader and (2) rear worklights (4) combination amber flashing warning lights Exterior lighting (2) tail and brake lights, (2) turn signal lights Portable service light w/ multiple combine connection points Cleaning sieve light (3) Rotating beacon lights (5) deluxe service lights under trim panels Pressure float override on height control system

  OPERATOR'S CAB:
  

  General: Tinted glass, w/ front sun visor LH entry and RH full view service door Tilt open rear window with dust deflector Breakaway exterior L & R rear view mirrors 1 center dome light Cab exit delay lighting Steering column with dual pivots & single telescope Two blade windshield wiper Windshield washer Fore/aft adjustable right console, floats w/ seat Air suspension operator seat Padded instructional seat w/storage compartment Operator and instructional seat belts Beverage and cell phone holder, ashtray and lighter Operator ladder w/ flexible lower step and forward storage position to clear uncut crop Automatic temperature control with heater/defroster and air conditioner Audible alarms for monitor system and grain tank full Mounting for electronic communication equipment

  General: 15 amp auxiliary power outlets (1) 12 volt single prong connector (2) 12 volt lighter outlets Operators manual w/storage compartment under operator seat Coat hook Radio ready with AM/FM antenna Business band antenna ready (coaxial cable)

  Right Console Controls:
  

  Backlit control switches Separator drive with rotor reverse Feeder drive with feeder reverse Auto/manual reel speed control Auto Header Height Control with fine adjust and 2 height settings Roading hydraulic safety lockout switch Unloader engage Unloader swing Separator engage Feeder/header engage Rotor speed Ground drive speed range selector Throttle, variable speed control Park brake Fan speed Concave position Straw and chaff spreader speed

  Multifunctional propulsion control lever:
  

  Propulsion control Feeder raise/lower, header tilt, reel raise/lower, reel fore/aft Unloader swing, unloader engagement Header height resume Feeder / header emergency stop "Select" control shift function: Headland turn sequence including header raise height Header fore/aft tilt Auto guidance nudge

  AFS ACCUGUIDE:
  

  Auto Guidance Ready Receiver mount Steering cylinder Steering Valve Mounting bracket for NAV II controller Wiring harness Antenna mounting bracket

  VEHICLE DISPLAY MONITOR:
  

  Engine power level Engine status/warnings Machine/operation status/warnings Hydraulic oil status/warnings ACS Crop presets for machine settings w/ additional programable settings Grain scan monitor Tailings volume monitor Header control settings Rotor speed Fan speed Concave position Display backlight control Configuration Setup & Calibration Diagnostics Shaft speed alarms Status indicators: Fuel level, digital bar graph Engine coolant temp graph

  THRESHING AND SEPARATING ROTOR:
  

  30 in. diameter AFX rotor Power Plus™ - CVT (Continuously variable transmission) rotor drive w/ 3 speed ranges (220 - 1200 RPM) Power Reverse - independent hydrostatic rotor reverser with in-cab control Easy access, adjustable transport vanes (adjustment on left hand side) Transition cone

  ROTOR MODULE FRONT:
  

  Quick change, 2 section, 4 piece (2LH, 2RH) bar and wire 180° of wrap Dual side access Electronic In-cab position control Interchangeable with rear modules

  ROTOR MODULE REAR:
  

  Quick change, 2 section, 4 piece (2LH, 2RH) 180° of wrap Dual side access Interchangeable with front modules

  GRAIN HANDLING:
  

  Grain tank capacity: 315 bushels (11,100 liters) Quick raise and lower grain tank extensions Foldable bubble up auger (2) Adjustable grain tank full sensors (50-75% and 75-100%) No tools required grain tank cross auger cover adjustment 3.2 bu/sec (113 liters/sec) unloading rate 13 inch diameter unloading auger Unloading auger spill saver Modulated hydraulic wet clutch unloader drive Electro-hydraulic controlled unloader swing Grain tank window Operator deck grain tank sample access

  Ground level clean grain elevator chain adjustment Wear resistant elevator head top sheet and boot door Radial pin slip-clutch torque protection Clean Outs: Clean grain and tailings auger drop-out troughs Clean grain elevator boot Front and rear grain tank cross auger doors (RH side) Vertical unload auger door

  RESIDUE MANAGEMENT:
  

  Dual disc, straw and chaff spreaders with adjustable spread width Perforated discharge beater/chopper pan Residue control modes: Spread chaff and straw Windrow chaff and straw

  MAXIMUM HEADERS:
  

  Grain Head - 30 ft. (9.1 m) Grain Head Flex - 35 ft. (10.7 m) Draper Head - 40 ft. (12.2 m) Corn Head (30 in.), 12-row Chopping Corn Head - 30 ft.

  Requirements for Operation:
  

  Header or corn head - refer to ordering guide

  THIS PRODUCT IS NOT AVAILABLE TO DEALERS HOLDING A LOW HORSEPOWER CONTRACT EX WORKS:
  

  Wholegoods (Ex Works Grand Island, NE) Factory Supplied Attachments (Ex Works Grand Island, NE)
• Axial-Flow 8120 Combine

  STANDARD FEATURES
  ENGINE:
  

  Diesel, 6 cylinder, Case IH 10.3L, 420 SAE hp Electronically controlled fuel injection Power rise - 60 hp Maxpower - 480 hp Complies with EPA Emissions Requirements (Tier 3) Air to air intercooler 277 gallon (1050 liter) fuel tank Key switch fuel/engine shut-off Water separator fuel filter and fuel cooler Water- in fuel sensor Air filter - dual stage dry type w/aspirated pre-cleaner In-cab service indicator 12 volt 185 amp alternator Two 12 volt batteries - 950 CCA each 24 volt starting system Engine grid heater Iso-mounted radiator, in-line core w/pressurized de-aerating tank Hinged, swing out oil cooler and AC cooler Metal rotary air screen

  GROUND DRIVE:
  

  Planetary drive, 125 cc pump and motor Electric shift 4 speed w/ hydrostatic drive Heavy-duty propulsion system 20 mph (32 kph) max road speed

  BRAKES:
  

  Manual dual caliper disc Electro-hydraulically released, spring applied park brake

  CHASSIS:
  

  Composite, hinged trim panels with transport locking pins Chassis jacking points Tie down shipping points Chassis tow points Tool box Service tool connection Combine reverse safety alarm Service platforms on both sides of chassis Fan bottom shield Two 10 lb. dry chemical fire extinguishers

  ADVANCED FARMING SYSTEMS:
  

  Yield and moisture sensors. AFS decals and badges.

  HYDRAULICS:
  

  Closed center load sensing system Single point/single lever header multi-coupler Electro-hydraulic control: Feeder raise/lower with variable rate control Reel fore & aft, raise/lower Unloader swing, Unloader drive clutch Separator Drive (Includes rotor drive, cleaning sieves, elevator drive and straw chopper drive) Feeder drive clutch Hydraulic Drives: Reel speed control Cross Flow Plus™ cleaning fan with speed control Dual straw spreader drive with adj. speed control Ride control feeder lift circuit accumulator

  FEEDER:
  

  Single lever header quick attach 54 in. (1,366 mm) wide Wear resistant floor and chain supports Undershot-serrated slat conveyor Four strand, 3 section conveyor with bolt on slats Mechanical shaft drive w/ modulated clutch engagement Independent hydraulic feeder / header reverser Feeder face adjustable fore & aft pitch Spring loaded front feeder drum Two 3 in. (75 mm) dia lift cylinders Friction type safety clutch for rock trap beater and independent radial pin safety clutch for conveyor chain Feeder safety stand

  CLEANING:
  

  Self leveling cleaning system Full width 15 in diameter Cross Flow Plus™ fan with speed control and clean out door Adjustable pre-cleaner sieve Active grain pan system Electronic in cab sieve adjust with opening indicator Full cleaning system width sieve grain loss sensor Tri-SweepTailings Processor System with cleanout door Tailings volume sensor

  ELECTRICAL:
  

  Data Bus serial communications system Exterior lighting (6) stadium roof lights (2) under cab after cut lights Left and right side lights (1) grain tank, (1) unloader and (2) rear worklights (4) combination amber flashing warning lights (2) tail and brake lights, (2) turn signal lights Portable service light w/ multiple combine connection points Cleaning sieve light (3) Rotating beacon lights (5) deluxe service lights under trim panels

  Exterior lighting Pressure float override on height control system

  OPERATOR'S CAB:
  

  General: Tinted glass, w/ front sun visor LH entry and RH full view service door Tilt open rear window with dust deflector Breakaway exterior L & R rear view mirrors 1 center dome light Cab exit delay lighting Steering column with dual pivots & single telescope Two blade windshield wiper Windshield washer Fore/aft adjustable right console, floats w/ seat Air suspension operator seat Padded instructional seat w/storage compartment Operator and instructional seat belts Beverage and cell phone holder, ashtray and lighter Operator ladder w/ flexible lower step and forward storage position to clear uncut crop Automatic temperature control with heater/defroster and air conditioner Audible alarms for monitor system and grain tank full Mounting for electronic communication equipment 15 amp auxiliary power outlets (1) 12 volt single prong connector (2) 12 volt lighter outlets Operators manual w/storage compartment under operator seat Coat hook Radio ready with AM/FM antenna Business band antenna ready (coaxial cable)

  Right Console Controls: Backlit control switches Separator drive with rotor reverse Feeder drive with feeder reverse Auto/manual reel speed control Auto Header Height Control with fine adjust and 2 height settings Roading hydraulic safety lockout switch Unloader engage Unloader swing Separator engage Feeder/header engage Rotor speed Ground drive speed range selector Throttle, variable speed control Park brake Fan speed Concave position Straw and chaff spreader speed

  Multifunctional propulsion control lever:
  

  Propulsion control Feeder raise/lower, header tilt, reel raise/lower, reel fore/aft Unloader swing, unloader engagement Header height resume Feeder / header emergency stop "Select" control shift function: Headland turn sequence including header raise height Header fore/aft tilt Auto guidance nudge

  AFS ACCUGUIDE:
  

  Auto Guidance Ready Receiver mount Steering cylinder Steering Valve Mounting bracket for NAV II controller Wiring harness Antenna mounting bracket

  VEHICLE DISPLAY MONITOR:
  

  Engine power level Engine status/warnings Machine/operation status/warnings Hydraulic oil status/warnings ACS Crop presets for machine settings w/ additional programable settings Grain scan monitor Tailings volume monitor Header control settings Rotor speed Fan speed Concave position Display backlight control Configuration Setup & Calibration Diagnostics Shaft speed alarms Status indicators: Fuel level, digital bar graph Engine coolant temp graph

  THRESHING AND SEPARATING ROTOR:
  

  30 in. diameter AFX rotor Power Plus™ - CVT (Continuously variable transmission) rotor drive w/ 3 speed ranges (220 - 1200 RPM) Power Reverse - independent hydrostatic rotor reverser with in-cab control Easy access, adjustable transport vanes (adjustment on left hand side) Transition cone

  ROTOR MODULE FRONT:
  

  Quick change, 2 section, 4 piece (2LH, 2RH) bar and wire 180° of wrap Dual side access Electronic In-cab position control Interchangeable with rear modules

  ROTOR MODULE REAR:
  

  Quick change, 2 section, 4 piece (2LH, 2RH) 180° of wrap Dual side access Interchangeable with front modules

  GRAIN HANDLING:
  

  Grain tank capacity: 350 bushels (12,330 liters) Quick raise and lower grain tank extensions Foldable bubble up auger (2) Adjustable grain tank full sensors (50-75% and 75-100%) No tools required grain tank cross auger cover adjustment 3.2 bu/sec (113 liters/sec) unloading rate 13 inch diameter unloading auger Unloading auger spill saver Modulated hydraulic wet clutch unloader drive Electro-hydraulic controlled unloader swing Grain tank window Operator deck grain tank sample access Ground level clean grain elevator chain adjustment Wear resistant elevator head top sheet and boot door Radial pin slip-clutch torque protection

  Clean Outs: Clean grain and tailings auger drop-out troughs Clean grain elevator boot Front and rear grain tank cross auger doors (RH side) Vertical unload auger door

  RESIDUE MANAGEMENT:
  

  Dual disc, straw and chaff spreaders with adjustable spread width Perforated discharge beater/chopper pan Residue control modes: Spread chaff and straw Windrow chaff and straw

  MAXIMUM HEADERS:
  

  Grain Head - 30 ft. (9.1 m) Grain Head Flex - 35 ft. (10.7 m) Draper Head - 45 ft. (13.72 m) Corn Head - 16-row 30 in. or 18-row 20 in. Chopping Corn Head - 30 ft. (9.1 m)

  Requirements for Operation:
  

  Header or corn head - refer to ordering guide

  THIS PRODUCT IS NOT AVAILABLE TO DEALERS HOLDING A LOW HORSEPOWER CONTRACT EX WORKS:
  

  Wholegoods (Ex Works Grand Island, NE) Factory Supplied Attachements (Ex Works Grand Island, NE) unless otherwise noted
• Axial-Flow 9120 Combine

  STANDARD FEATURES
  ENGINE:
  

  Diesel, 6 cylinder, Case IH 12.9L, 480 SAE hp Electronically controlled fuel injection Power rise - 43 hp Maxpower 523 hp Complies with EPA Emissions Requirements (Tier 3) Air to air intercooler 277 gallon (1050 liter) fuel tank Key switch fuel/engine shut-off Water separator fuel filter and fuel cooler Water- in fuel sensor Air filter - dual stage dry type w/aspirated pre-cleaner In-cab service indicator 12 volt 185 amp alternator Two 12 volt batteries - 950 CCA each 24 volt starting system Engine grid heater Iso-mounted radiator, in-line core w/ pressurized de-aerating tank Hinged, swing out oil cooler and AC cooler Metal rotary air screen

  GROUND DRIVE:
  

  Planetary drive, 125 cc pump and motor Electric shift 4 speed w/ hydrostatic drive Heavy-duty propulsion system 20 mph (32 kph) max road speed

  BRAKES:
  

  Manual dual caliper disc Electro-hydraulically released, spring applied park brake

  CHASSIS:
  

  Composite, hinged trim panels with transport locking pins Chassis jacking points Tie down shipping points Chassis tow points Tool box

  Service tool connection Combine reverse safety alarm Service platforms on both sides of chassis Fan bottom shield Two 10 lb. dry chemical fire extinguishers

  ADVANCED FARMING SYSTEMS:
  

  Yield and moisture sensors. AFS decals and badges.

  AFS ACCUGUIDE:
  

  Auto Guidance Ready Receiver mount Steering cylinder Steering Valve Mounting bracket for NAV II controller Wiring harness Antenna mounting bracket

  HYDRAULICS:
  

  Closed center load sensing system Single point/single lever header multi-coupler Electro-hydraulic control: Feeder raise/lower with variable rate control Reel fore & aft, raise/lower Unloader swing, Unloader drive clutch Separator Drive (Includes rotor drive, cleaning sieves, elevator drive and straw chopper drive) Feeder drive clutch Hydraulic Drives: Reel speed control Cross Flow Plus™ cleaning fan with speed control Dual straw spreader drive with adj. speed control Ride control feeder lift circuit accumulator

  FEEDER:
  

  Single lever header quick attach 54 in. (1,366 mm) wide Wear resistant floor and chain supports Undershot-serrated slat conveyor Four strand, 3 section conveyor with bolt on slats Mechanical shaft drive w/ modulated clutch engagement Independent hydraulic feeder / header reverser Feeder face adjustable fore & aft pitch Spring loaded front feeder drum Two 3 in. (75 mm) dia lift cylinders Friction type safety clutch for rock trap beater and independent radial pin safety clutch for conveyor chain Feeder safety stand

  CLEANING:
  

  Self leveling cleaning system Full width 15 in diameter Cross Flow Plus™ fan with speed control and clean out door Adjustable pre-cleaner sieve Active grain pan system Electronic in cab sieve adjust with opening indicator Full cleaning system width sieve grain loss sensor Tri-SweepTailings Processor System with cleanout door Tailings volume sensor

  ELECTRICAL:
  

  Data Bus serial communications system Exterior lighting (6) stadium roof lights (2) under cab after cut lights Left and right side lights (1) grain tank, (1) unloader and (2) rear worklights

  Exterior lighting (4) combination amber flashing warning lights (2) tail and brake lights, (2) turn signal lights Portable service light w/ multiple combine connection points Cleaning sieve light (3) Rotating beacon lights (5) deluxe service lights under trim panels Pressure float override on height control system

  OPERATOR'S CAB:
  

  General: Tinted glass, w/ front sun visor LH entry and RH full view service door Tilt open rear window with dust deflector Breakaway exterior L & R rear view mirrors 1 center dome light Cab exit delay lighting Steering column with dual pivots & single telescop Two blade windshield wiper Windshield washer Fore/aft adjustable right console, floats w/ seat Air suspension operator seat Padded instructional seat w/storage compartment Operator and instructional seat belts Beverage and cell phone holder, ashtray and lighter Operator ladder w/ flexible lower step and forward storage position to clear uncut crop Automatic temperature control with heater/defroster and air conditioner Audible alarms for monitor system and grain tank full

  Right Console Controls:
  

  Backlit control switches Separator drive with rotor reverse Feeder drive with feeder reverse Auto/manual reel speed control Auto Header Height Control with fine adjust and 2 height settings Roading hydraulic safety lockout switch Unloader engage Unloader swing Separator engage Feeder/header engage Rotor speed Ground drive speed range selector Throttle, variable speed control Park brake Fan speed Concave position Straw and chaff spreader speed

  Multifunctional propulsion control lever:
  

  Propulsion control Feeder raise/lower, header tilt, reel raise/lower, reel fore/aft Unloader swing, unloader engagement Header height resume Feeder / header emergency stop "Select" control shift function

  OPERATOR'S CAB: (continued)
  

  Multifunctional propulsion control lever: Headland turn sequence including: Header raise height Header fore/aft tilt Auto guidance nudge

  VEHICLE DISPLAY MONITOR:
  

  Engine power level Engine status/warnings Machine/operation status/warnings Hydraulic oil status/warnings ACS Crop presets for machine settings w/ additional programmable settings Grain scan monitor Tailings volume monitor Header control settings Rotor speed Fan speed Concave position Display backlight control Configuration Setup & Calibration Diagnostics Shaft speed alarms Status indicators: Fuel level, digital bar graph Engine coolant temp graph

  THRESHING AND SEPARATING ROTOR:
  

  30 in. diameter ST rotor Power Plus™ - CVT (Continuously variable transmission) rotor drive w/ 3 speed ranges (220 - 1200 RPM) Power Reverse - independent hydrostatic rotor reverser with in-cab control Easy access, adjustable transport vanes (adjustment on left hand side) Transition cone

  ROTOR MODULE FRONT:
  

  Quick change, 2 section, 4 piece (2LH, 2RH) bar and wire 180° of wrap Dual side access Electronic In-cab position control Interchangeable with rear modules

  ROTOR MODULE REAR:
  

  Quick change, 2 section, 4 piece (2LH, 2RH) 180° of wrap Dual side access Interchangeable with front modules

  GRAIN HANDLING:
  

  Grain tank capacity: 350 bushels (12,330 liters) Quick raise and lower grain tank extensions Foldable bubble up auger (2) Adjustable grain tank full sensors (50-75% and 75-100%) No tools required grain tank cross auger cover adjustment 3.2 bu/sec (113 liters/sec) unloading rate 13 inch diameter unloading auger Unloading auger spill saver Modulated hydraulic wet clutch unloader drive Electro-hydraulic controlled unloader swing Grain tank window Operator deck grain tank sample access Ground level clean grain elevator chain adjustment Wear resistant elevator head top sheet and boot door Radial pin slip-clutch torque protection Clean Outs: Clean grain and tailings auger drop-out troughs Clean grain elevator boot Front and rear grain tank cross auger doors (RH side) Vertical unload auger door

  RESIDUE MANAGEMENT:
  

  Dual disc, straw and chaff spreaders with adjustable spread width Spring loaded, perforated discharge beater/chopper concave Residue control modes: Spread chaff and straw Windrow chaff and straw

  MAXIMUM HEADERS:
  

  Grain Head - 30 ft. (9.1 m) Grain Head Flex - 35 ft. (10.7 m) Draper Head - 45 ft. (13.7 m) Corn Head - 16-row 30 in. or 18-row 20 in. Chopping Corn Head - 30 ft.

  Requirements for Operation:
  

  Header or corn head - refer to ordering guide

  THIS PRODUCT IS NOT AVAILABLE TO DEALERS HOLDING A LOW HORSEPOWER CONTRACT EX WORKS:
  

  Wholegoods (Ex Works Grand Island, NE) Factory Supplied Attachments (Ex Works Grand Island, NE)